FFHT1821TW2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Mansfield, OH
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace meat drawer support
Removed glass shelf and frame. Unscrewed support from frame,replace with new support and screwed it into the frame, attach drawer and replace shelf in fridge .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from GENOA CITY, WI
- Parts Used:
- 240358008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong size
I sent the rack back to the address on the invoice and never received a refund. I was never able to get through on the phone line to speak with someone or to leave a message.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BRONX, NY
- Parts Used:
- 240534901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bar had broken
Simply replaced by hand. No tools necessary
Was this instruction helpful to you?
Thank you for voting!
Old gaskets were cracked. Not a good seal.
Pulled old gasket off. Then put new gaskets on starting on one corner and pressing in all around. Took 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from MARKLEYSBURG, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The slide rail(Drawer Support Rail) I found was made very cheaply. None the less I had to replace it. I did watch the Repair tutorial on your site that made the repair a snap. Ezpeeze!
Removed the shelf and one screw on the back of the rail. Replaced rail and screw. Re-inserted the drawer and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from EDGEWATER, MD
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rail broke
remove one screw attach new rail....done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mikaeline from SYCAMORE, IL
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rail replacement
Removed shelf from frig. Removed screw of broken rail. Replaced with new rail with screw. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TALLAHASSEE, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawaer support on right side of top shelf broke
Unscrewed screw from back of shelf pulled broken part out of slot it holds in and replaced with new one screwed the piece back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from FENTON, MI
- Parts Used:
- 240358008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer shelf was showing rust & needed to be replaced
Removed old shelf & popped in the New one. Very easy ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from COTTONWOOD, CA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Draw support rail broke.
Removed top shelf. Removed rail screw and old rail. Install new rail and use rail screw to secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SENECA, SC
- Parts Used:
- 240530701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Matching up the mounting screw.
A single screw holds the part in place. The ONLY challenge is seating the new slide so that the screw hole in the glide matches the hole in the support assembly. Initially setting the glide into place mismatched by about 1/16 of an inch toward the back of the refrigerator. Firmly grasping the new part after mating it to the two receivers on the support assembly, pull it toward you until it clicks into place. The screw should mate cleanly to the new part without any difficulty. Make sure you get the right or left side part, as they are not interchangeable.
Was this instruction helpful to you?
Thank you for voting!
Broken door shelf, front rollers cracked
I installed door shelf myself. Very easy. My son and grand did the roller repair. This was fairly easy but the reason I had them do it was to tilt the refrigerator over to reach. Needed man power!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from DANSVILLE, NY
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Blown bulb
Did get bulb from another company replaced bulb was told to hang on to the three bulbs for 30 days if they don't send return label in 30 days throw them out at 95 dollars each
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from MARYVILLE, MO
- Parts Used:
- 240337712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement door for the dairy compartment
It simply snapped into place. No tools required. A very simple repair.
Was this instruction helpful to you?
Thank you for voting!