FRSS26L3AF9 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pete from THE PLAINS, OH
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dispenser Crusher Housing was broken
I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Avrum from Boynton Beach, FL
- Parts Used:
- 241786014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
Had frost in freezer of side by side. Did dollar bill test and determined that gasket was not sealed.
Consulted You Tube. Took off old gasket. Easy. Put on new one after getting it warm. The track on the new gasket did not sit properly. Took multiple attempts but finally worked. Size was perfect but the gasket color was different than original and therefore, different from the refrigerator door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Berthoud, CO
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Part broke though normal use
Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from LIVERMORE, CA
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The ice crushing housing was broken.
The repair went easily after watching the video, took me less than an hour to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from INVER GROVE, MN
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Every part of the ice crusher (blades and housing) bent/broke in successive failures
This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from CATSKILL, NY
- Parts Used:
- 5304525957
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
During a recent move, they had to remove the doors, so they removed the top two door brackets.
The repair was quick and easy. Just install the ordered bracket ( hinge ) on the top refrigerator door and cover. I had all the screws and cover but somehow the original bracket was missing...hummm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from WEIRTON, WV
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Plastic gate to redirect ice to the crusher broken off
Removed ice maker bin...removed screws and housing and reinstalled all...very easily completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from PADUCAH, KY
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ice maker stoped crushing ice
i watched the video very simple repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joy from lacey's spring, AL
- Parts Used:
- 241786014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I was getting thick frost buildup in the upper right corner and my water line was freezing
The repair instructions were suspiciously easy sounding- but in actuality- right on! I am not a DIY-er , but I did it! The old gasket came off fairly easily and the new one went right on! No tools needed! There wasn’t an immediate ‘suction/seal’ when I closed the door, but Grok said that was normal, it may take a little time… Sure enough- in the morning it was tight! That’s been 2 weeks and so far- so good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from Langhorne, PA
- Parts Used:
- 241885001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Freezer leaked, no water disp. & Crusher didnt crush
First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from BRIDGEPORT, NE
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Installation of Frigidaire Housing crusher assy.
I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755405
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from S SAN FRAN, CA
- Parts Used:
- 241786014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer door seal shrunken,icing up,constant running
Pulled door seal put and pushed in new seal, icing formed on fridge side lower return vents, had to fully chip away, compressor running and stopping as normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from SILVER SPRING, MD
- Parts Used:
- 5304522314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulb burned out
replaced bulb
Was this instruction helpful to you?
Thank you for voting!