FLHS269ZCW1 Frigidaire Refrigerator - Instructions

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

I ordered a new shelf and I put in, less than minute

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

The repair was very easy. I loosened the two screws holding the icemaker onto the side of the freezer, then unplugged the icemaker. Reversed the order, and it was done. You have to shut the water off first.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

Replaced the Triple Water Valve

Looked at video on how to remove and reinstall support and followed the instruct ions

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

I removed the filter bypass from the box. I opened the refrigerator door. I put the filter bypass in the space where the filter was located. I closed the refrigerator door. I opened the freezer door. I turned on the ice maker. It worked.

I ordered 3 bins initially and received only one, which was very easy to install. It just snaps in. When I called to indicate that I had received only one of the 3 bins, a claim was submitted and I got a refund for the missing parts. Then I had to reorder the two missing parts.

When I received the reorder, both of the bins were broken. I called to indicate that they were broken. I was told that I would have to submit photos of the broken parts to [email protected], which I did. After I submitted the photos, I received an email asking me for the photos again and the serial number of the refrigerator. This is the first time the serial number was requested. I have no idea why they wanted the serial number at this point instead of when I first ordered the parts.

At this point, I am still waiting to get my claim for the broken parts approved. I assume that the shipping department is pretty worthless, since they screwed up my order to begin with and then the shabby packing that was done for such fragile plastic parts on the reorder.

I'm not happy with the hassle that I have been going through just to get a simple order delivered.