FRSR25V5AW3 Frigidaire Refrigerator - Instructions

Easy Job. First I removed the plactic drip tray exposing the three phillups head screws. (use a good screwdriver). The top area pops out by moving the assy upward. Disconnect the wiring harness and remove the outer assy leaving the iner assembly accessible. A spring holds the broken part in place and if its still together like mine you can reinstall it the way it appears. Make sure the wiring harness goes in firmly and you should have no problems.

Exposed and removed the screws at the top of the door. Removed and replaced the bearing and plate on the bottom of door and put it back together. Honestly, this is the easiest repair I ever made. The biggest chore was removing the contents of the door before taking the door off. Also was working alone, an extra pair of hands to hold the door would have been helpful but not necessary.
Be prepared to never hear that horrible clunk again!

turned ice maker water off.Removed housing with 1/4" nut driver.disconnected water lines that had quick disconnect.(pushed bottom plastic washer up & popped off.unscrewed old filter cup off with nutdriver. Screwed new one in place,put filter in cup & screwed on,pushed water lines on.put housing back on & turned water on. No leaks & had my ice maker back in working order,also my water on front door.was easier than expected.lady was very helpful when ordering cause I was worried it may not be same one cause was slight difference in appearance.but it matched up to model number & ended fitting just fine,also was shipped very quick,1 day & it was at my door.nice to have ice again,thanks part select.

On the bottom edge of the ice maker the half inch strip slides away from refrigerator. Under the strip is 3 phillips screws. The screws release the plastic frame. On the switch panel are 3 screws which release the button panel. I unplugged 1 connector to left side of switchs freeing the switch panel. I pulled the spring over to the left that holds the lever tight. I was then able to remove 3 small screws that hold the lever in place. I just inserted the new part and in reverse assembled all parts back. It really was a no brainer. I really feel good not having to pay $100.oo for a service call.

I cleaned out the refrig door, unbolted it from the top and removed the door. Then I replaced the broken plastic parts, reinstalled the door and bolted it back up. Very simple, very easy!

plug and play. removed old one, and install new one.

watched the video, ordered the part and handed it to my husband. He quickly removed the hinge cover and took it apart--the lower door bearing was tightened with glue which made it difficult but once that was out of the way, it was remove, assemble and back in business. Thanks for making it "do-able". C and D in New Mexico.

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Removed ice maker bin...removed screws and housing and reinstalled all...very easily completed.

My 12 year old did this himself. Took plastic cover off and removed old part and screwed in new part.

Put a new door bearing and problem solved

When my parts arrived I took a screwdriver and removed the hinge cover on the top of the refrigerator door. I then took a 3/8 drive ratchet and a 3/8 socket and removed the 2 screws on top of the fridge that hold the door hinge on( be sure to empty your door before you take the bolts out). I lifted the door out and layed it in the floor and upon inspection I found that the hinge bearing that fits inside the bottom of the door was completely broken off. I had to take a flat screwdriver and dig it out enough to grab it with a pair of pliers and pull it out. I inserted the new bearing and made sure it was all the way in then applied some petroleum jelly around it and the door closing cam. My door closing cam was still good so I didn't have to replace it. I lifted the door and placed it back in the hole on the bottom, closed the door, reinstalled the hinge on top, adjusted the door, tightened the bolts and reinstalled the hinge cover. Piece of cake thanks to the video on the web site!!! I know from now on where to go for parts I need for any of my appliances. Thanks !!!!!

Replaced Ice Container/Bucket

The video was an amazing tool. I have never repaired anything on an appliance before and I was able to follow the instructions easily.

I watched the video on line after identifying the proper parts I needed. When the parts arrived I followed the easy instructions I had watched and proceeded to turn off the unit and remove the items and shelves from the door and then removed the cover plate and two screws from the bracket holding the door in position. Laying the door on a blanket I was able to quickly remove the broken part and insert the new plastic bearing in place. I then removed the plastic part on the lower bracket and installed the new piece. The door was easily put back on the refrigerator and was aligned perfectly. Putting shelves and items back in place was still less then the fifteen minutes time.