FRSR25V5AW1 Frigidaire Refrigerator - Instructions

just followed the instructions

Wasn't sure what parts to replace so happy to find intact entire assembly. Popped out the old, popped in the new. Back in business in less than 5 mins. Highly recommend.

Took out the out one and slid in the new one so easy to do

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

first removed three screws holding cover un snap water lines remove two screws holding filter housing up reinstalled new parts

followed instructions on your video.. PERFECT and easy.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

Remove filter housing cover (one 1/4" hex screw). Remove the quick disconnect water lines. Replace filter housing with new (two 1/4" hex screws). Reconnect water lines. Reinstall cover.

The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches

i ordered a replacement, and when it came in i took the old part off and installed the new dispenser. it works great.

The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

Followed the video for this repair. Only issue was that the videos showed that when the front panel is removed, there is a wire harness that has to be unplugged from part No. 38c. This was not the case. What I had was a Ribbon Cable Harness that plugged into the front of part No. 38 and the top of part 38C (the two power boards) I tried to disconnect it from part 38C by pulling it out, and apparently damaged the Ribbon Cable Harness. Later found a video showing how to remove this item properly when replacing power boards 38 and 38C. Have ordered a new cable from GRP and hopefully this will solve the problem, as there is no electrical current to the dispenser controls and the ice and water dispenser are not currently working. Would have been nice to know that there are two types of connections between these power boards; a cable harness that unplugs from 38C or a Ribbon Cable Harness that unplugs from from the face of part No. 38. Hopefully I have not damaged either of the boards or anything else. Professional repair man coming on Thursday to test the boards, micro switches, etc. The boards are quite pricey, ($550.00 for both) and since the refrigerator was manufactured in 2004, we will buy a new one before we pump any more into this older unit. Very important to know how to unplug this Ribbon Cable Harness from the boards before proceeding ! Plug in on 38C is very tricky and you will need to review a video showing how it is done.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

The repair went easily after watching the video, took me less than an hour to complete the repair.