FRSR25V5AQ3 Frigidaire Refrigerator - Instructions

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

First I cleaned out the side door then, removed the three screws on top of the door. Lifted the door off and set it carefully on a kitchen mat.

I had to use the pliers to remove the existing bearing hinge as it had disintegrated in the door. Once it was out the new hinge slid right into place and I reinstalled the door. I had help with the door. It’s much easier with two people to get proper alignment and to hold it in place while you reattach the screws.

I would have to say the hardest part of this repair was cleaning out the refrigerator.

Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Used pliers to remove filter.

I removed the old housing (three screws) , pulled it out about three inches and discounnected the two water lines. Then I put the new one on, attached the two water lines & I had water immediately & ice within a couple of hours.
Really it was a no brainer, but I'm sure I saved at least $50 doing it myself.

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

just removed the screws, pulled off the hose and replaced with the new ones. So easy and saved about $175.00 doing it ourselves.
(That was the best part)

Discovered water filter housing broken allowing water to leak out when using water in door function.
Found part number using Part Select diagrams. Ordered part from Part Select,. shipping time about 3 days.
Removed 3 screws houlding from cover over housing assembly. Removed cover, removed old, broken part by pulling water lines from top of unit. Replaced new housing in place, connected above mentioned water lines, replaced cover and holding screws. Tested for leaks. Everything worked great.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Looked at video on how to remove and reinstall support and followed the instruct ions

First I unplugged the refrigerator.
Then I removed the drip tray to gain access to the three screws that supported the module cover. The three screws were rusted into place and required a square No. 1 bit to remove. Once I finally found the right bit that fit, with much effort, I removed the three rusted screws and the module being careful to unplug the circuit board cable from the module back.
I used a NON magnetic screwdriver to remove the 4 screws that held the circuit board on the back of the module cover. I removed the cover, power board, carrier and light module and put it on the new module cover I also bought (because it was broke due to the rusting of the screws). I made sure I stayed in full contact with the circuit board and module cover at the same time to avoid static discharge from the new board from the static wrapper to the module cover because static discharge may damage the fragile microchips in the new board.
Once the pieces were in place, I put back on the back cover and 4 screws with a NON magnetic screwdriver.
I pealed the Module cover lable off the old cover and pressed it on the new module cover. (A new sticker cover cost more than a circuit board).
I reattached the circuit board cable and replaced the module. I screwed in three new phillip screws and placed back in the drip tray.
I plugged in the refrigerator and no more problem with the Ice and water maker being intermitten.

Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

three screws out after turning off the water supply
remove 2 hoses from top of the system replace the system and then the cover with the 3 screws all was good to go after the 2 hoses were popped back on and the water turned on at valve

this would have been way faster if my husband ley me do it haha he kept dropping the screws so we had to pull all drawers out to find 10 max

I unscrewed the cover, took out old filter, put in new filter and replaced cover. End of story. Oh...don't forget to turn off the incoming water supply.