FRS26ZTHB5 Frigidaire Refrigerator - Instructions

Simply unscrewed cover on water filter and pulled old filter out. New filter comes with o-ring on filter. Simply reversed procedure and installed new filter.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

The part’s picture on the site was not identical to the part delivered, but the function was essentially the same. It had different connectors to the outgoing tubes and a slightly different method of attachment to the refrigerator (it required 1 additional skew - not included). After verifying the part would still work, I shut off the water. Then I disconnected the two outgoing tubes. Made sure I had bucket handy to handle excess water. Then I removed the part using an adjustable wrench (1 screw) and then detached the incoming tube. Attached the incoming tube to the new part and then remounted (2 screws). And then I attached the two outgoing tubes and turned on the water. It works great and I have no plumbing experience.

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

Removed parts and reused the old rollers from the sliding meat drawer. Important point to remember is to not through away any hardware before the new parts arrive. New parts are void of hardware. Parts arrvied ontime as promissed and fit perfectly. I saved a ton of money doing this myself and not calling the repairman. great experiance.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

Replacing the old drawers out for the new ones was so easy that my 13 year old son took less than 15 minutes to do the job! By himself!
He pulled out the two old broken drawer,s took off the front panel,s on each, put the panel on their respective new drawer , filled the drawer up with the veggies that were in it before, and put the whole thing back in the fridge! Now my drawers work again and don't fall out or crack each time I open them! Hooray for replacement parts!!! Saved me a bundle on buying a new fridge!

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)