FRS23W3AQ0 Frigidaire Refrigerator - Instructions

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

Before removing door, remove everything from on the door including the shelves, then close the door. Using a step ladder to access the top of the door, I removed the plastic hinge cover at the top of the refrigerator door using a Philips head screwdriver, remove the screw located at the back of the cover and slide the cover forward and up to remove. This will expose the two 3/8 machine screws that hold the top hinge bracket. Remove the screws using a socket or wrench. Then lift up on the hinge bracket from the top of the door to remove it. As long as the door is closed it will remain stable with little pressure to keep from falling. Then lift the entire door from the bottom hinge assembly and lay it across an arm chair or flat elevated surface so you can access the bottom door hinge bearing. You will see a bracket screwed to the bottom of the door with two 1/4 machine screws, it is the door stop bracket and this has the door hinge bearing inserted through it. My bearing was broke in half , the first piece fell out when I removed the door and the other piece was still inserted in the door. I removed one 1/4 screw from the stop bracket and loosened the other screw to allow the bracket to swing away from cavity that holds the bearing. Using needle nose pliers I remover the broken piece of the bearing. This part is nylon or plastic and can be cut into pieces if need be to remove it. Once removed, I cleaned the cavity, reinstalled the stop bracket assembly then inserted the new bearing. Gently align the door to the bottom bracket and set it in place, a second set of eyes may help. Once the door has been seated and in the closed position replace door bracket and the two 3/8 screws at the top of the door, check the alignment before you tighten. Check door operation! Then tighten the screws and replace the plastic cover by pressing down on the cover and sliding it back to align the Philips screw to be replaced .

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

The repair was simple as described by another customer. One additional note, the water line is tight and can be difficult to remove. Extra slack is available under the fridge. Just push the slack up remove the water line. When the repair is complete reinstall the water line, pull the extra slack back from under the fridge.

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

removed ice denspenser and replaced spring and flap'

Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.

Thank you

Liz

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.