GRSS2652AF6 Frigidaire Refrigerator - Instructions

Every time I spoke to someone they sent wrong part . Still do not have correct part. Plus had to pay to return part. I sent model number , bin number and they can’t seem to match. Afraid to try again.

Followed the simple instructions on the device and in the appliance use and care manual

Unscrew a few screws and remove some plastic covers to access the ice cube tray. Undue two wire connections and remove the tray. Put in the new unit in reverse order. I heard it may take awhile for the new ice maker to start doing anything. Mine didn't do anything for 6 hours, then made it's first batch. Making ice fine now ever since.

Located problem part of ice maker on web site. Picked the part that had the highest percentage of being the the part that was broken (58% I think). Removed the part, waited for the new part, then put it all back together. Simple. It works great. Thanks for having such an easy web site to diagnose the problem.

there is no visible way to remove the old one i have spent hours on line and on the phone with tech support with no results . and have a complete parts diagram.this unit is less than one and a half years old manufactured 9/21 i will never buy frigidaire again

Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

installed end piece onto the glass and placed it in the freezer at the known shelf location

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.

Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order

Full steps followed
https://www.youtube.com/watch?v=73rubWwQork

Consulted You Tube. Took off old gasket. Easy. Put on new one after getting it warm. The track on the new gasket did not sit properly. Took multiple attempts but finally worked. Size was perfect but the gasket color was different than original and therefore, different from the refrigerator door. No tools required.

My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.

Remove the drawer, and everything you have on the top glass of the rail. Push the rail upward and pull towards you. Remove the two clips from old part and place them on new part. Place the new part using the same steps. Remember to hold the two clips in place.

I looked at the internet before I purchased a new seal and saw how to repair it. It was a matter of pulling out the old seal and just popping in the new. The internet said to use a hair dryer to melt the rubber to adhere to the fridge in places where it wasn't. It was quick!