FRT26XGCD4 Frigidaire Refrigerator - Instructions

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

Shut down Freezer/refrigerator. Disconnected water piping. Extracted old water valve. Replaced with new one. Turned on water and power.
Result, Ice cubes.

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

I could hear the pump activating....the sound of the pump, but no water coming to the ice maker.
Finally, a minor flood in the basement, below the fridge. Pressure in the water line from the pump up the back of the fridge to the area of the ice maker...let go, sending water all over the place.
I had tried emptying the contents of the fridge and the freezer to attempt to let the line thaw, in case that was the problem, but I hadn't waited long enough. It took 2 days to thaw the frozen water in the line to the ice maker..... but that was the problem.
Interesting! the fridge and frezzer have independent thermostats, but when I turned down the freezer thermostat...the fridge went warm as well . The dual outlet water valve I bought, I'll just keep.

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

It was just a simple replacement, three nuts to loosen , a slight adjustment on the timer and reversal installation...As simple as replacing a light bulb! You needn't be a brain surgeon to do this job! Your installation video was very helpful....Thank you PartSelect Chuck McCann

found leak and ordered parts came in two days will use your service again