GS21HTZDPB5 Frigidaire Refrigerator - Instructions

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

I called in because the model # of the refrigerator did not show up on the website. The cust. srvc. rep looked it up and found the part. It was reasonably priced, I received it in a matter of days and it fit perfectly. Thank you! We were preparing to put the condo on the market and broke the shelf while cleaning. It was great to have a resource for a reasonably priced replacement and quick shipment.

I removed the glass from the cover, removed the 2 crispier pans and removed and discarded the broken cover. I installed the new cover by making sure the back was flush against the back wall of the refrigerator. After that I replaced the glass and drawers and it was as good as new.

Unscrewed the lower back cardboard panel and removed it. Unplugged refrigerator. Reached in and took the metal piece off that keeps the starter from coming off. Pulled the starter off the compressor. Unplugged the starter from the power line. Replaced starter. Hooked power line back on. Hooked starter to the compressor. Put the metal piece back on to hold in place. Plugged refrigerator back in. Put back panel back on.

actually viewed short U tube video which helped..The top 2 screws are routine but initially didn't understand how the handle "hooked" on the screw at the bottom.Customer service very helpful when I called and had to return the incorrect handle I had ordered. Part came right away.

I ordered the part, it arrived within 48 hours. I opened the fridge and put the shelf in perfectly!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.

Pulled out the old one and popped in the new one

removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do

Easy peasey just slipped it in

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

I broke the glass shelf in my refrigerator. I had trouble navigating the website, so I called the customer service line, and the lady was lovely to speak with, and ordered my part quickly! In 2 days I had the part, and it fit perfectly!

Great service, great price!
Thank you!