FRSS2623AW1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from SILVER SPRING, MD
- Parts Used:
- 5304522314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulb burned out
replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from COOSADA, AL
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The ice crusher housing is made of plastic and a piece of it broke off,
Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nathan from Buckley, WA
- Parts Used:
- 241657502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Installed a extra shelf
Pushed the shelf pegs in the wholes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Allegany, NY
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The ice crusher flap was broken.
Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Lehigh Acres, FL
- Parts Used:
- 241786014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I noticed ice on the inside of freezer door
The young lady that helped me was fantastic... great product knowledge and affermed the correct and we got it ordered... Fast shippers and the install was easy although there were no instructions to be had... checking the gasket and removing the old one,,, it pressed in place in moments... They are booked marked and will use them the next time...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore l from jacksonville, FL
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The gasket was torn.
The gasket arrived in two days as advertised. Removal was easy and did not require any tools. The new gasket was simply pushed into place. It was so simple and easy, I thought more was required. I will definitely use this vendor again !
Was this instruction helpful to you?
Thank you for voting!
old seals on both fridge doors
pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Hockley, TX
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Stop crushing ice.
Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maridell from Lexington, SC
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace split door seal
It took about 5 minutes to pull the old seal out and replace with the new one. Simple enough for a 71 year old woman to do alone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Saranac, MI
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Seal was broken
Pulled out the old seal by hand. Cleaned the opening. Pressed the new seal in place. The entire process took about five minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orlando, FL
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn fresh food door gasket
Removed the old gasket and installed the new one. Really, really easy to do. Took me about ten minutes.
Was this instruction helpful to you?
Thank you for voting!