FRT24TGCD4 Frigidaire Refrigerator - Instructions

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

Loosened 2 screws, lifted icemaker brackets off of loosened retaining screws, unplugged electrical connector from the icemaker.
plugged in the supplied jumper harness & connected to the new icemaker, hung it on the loosened screws, secured the 2 screws.
Dranke beer & listened to my new icemaker rock & roll.
No further problems, Frigie like new.
The price was the cheapest I could find. $78.00 total including shipping.
A little girl could replace this unit.

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

I removed the retainer bar from the freezer door and unclipped the broken end cap (the clips were broken). I snapped the new one into place and snapped the retainer bar back into the freezer door.

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.