F44C21IBD0 Frigidaire Refrigerator - Instructions

just had to loosen the old, broken piece, and snap in the replacement. Piece of cake

Put the new shelf into position-Voila!

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!

Purchased a new ice maker assembly and installed. Very easy

We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinstall the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.