FGSS2335TF9 Frigidaire Refrigerator - Instructions

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Took out old replaced with new. Now it makes ice

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Basically unhooked water lines and removed the screws

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

Had to replace with a whole new part, had to take it all apart to replace

very easy, make sure to watch the provided you tube video.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

slide old filter out and insert new one

Just popped the new bin into place with my thumb. I also wanted to say. . . Don't bother with express or overnight delivery. I ordered the new bin on a thursday, paid for 3-5 day delivery and it arrived the next day. Installed it in less time than it took me to unwrap it.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike