FFSS2615TS5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nina from Deerfield Beach, FL
- Parts Used:
- 240350702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The frame for the upper crisper drawer cover was cracked.
So simple! I just slid the drawer out of the old frame, inserted it in the new one, and added the glass cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from DAYTON, OH
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
After a power outage my refrigerator went warm & the freezer was cool.
I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Detroit, MI
- Parts Used:
- 241786014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer door gasket became loose
Followed instructions for this part from this site and things went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shellie from MONCKS CORNER, SC
- Parts Used:
- 241786014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Freezer started icing up. Gasket was torn in places letting air in.
The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MILTON, DE
- Parts Used:
- 5303918214
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
Freezer not holding temp
The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from DANSVILLE, NY
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Fridh light bulb blew
Got sent the wrong bulb 3 times had to pay for the three bulbs 75 dollars each Sent pictures of right bulb still wrong bulb no refunds for 30 days I even gave them right part number. Found out that the part number on box but wrong bulb inside told them and they seem not to care ordered from another company still out 225 dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from TONEY, AL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
ice maker would not dispense cubes, stuck on crushed ice
turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ellsworth, WI
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker line was freezing
Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Clayton, NC
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
crusher housing cracked
Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Seneca, NY
- Parts Used:
- 241993101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken shelf support
I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SOCIAL CIRCLE, GA
- Parts Used:
- 242126602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the shelf in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from buffalo, NY
- Parts Used:
- 242126602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked bin
Inserted unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HILLIARD, OH
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame of meat drawer cracked
Took out old frame by removing drawer then lifted frame out. Lifted glass panel out of frame, place glass panel in new frame, places frame back in refrigerator and slid drawer back in. Easiest repair ever and I repair nothing myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory L from LAS VEGAS, NV
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame had cracked from weight of items nd age of frame.
Removed all items from glass top then removed drawer from frame. Removed damaged frame. Transferred glass top to new frame and installed new frame. Reinserted drawer. E Z P Z
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Chesapeake, VA
- Parts Used:
- 241969501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken frame
removed broken one and slid in new one, put in glass.
Was this instruction helpful to you?
Thank you for voting!