CFUM21PW1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dylan from Celina, OH
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke at the attachment point on the door
removed two pieces of trim.....removed four screws of old handle.....replaced with new handle....replaced screws.....replaced trim pieces
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Roseburg, OR
- Parts Used:
- 297283900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Needed a left hand hinge
The left swing hinge (297283901) that i needed is not available anywhere so I bought the right swing hinge (297283900), used a hydraulic press to pop out the pin and move it to the other hole. After that it was real quick to remove the screws and change out the hinge, changing the swing of the door. It is easiest to remove the top hinge and door first when doing this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from FORT WAYNE, IN
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke off of the refrigerator
Was able to order the handle and screw it on the refrigerator using the screws from the original handle in about 10 to 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Salt Lake City, UT
- Parts Used:
- 297311201
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge door handle broke off, replaced it.
Very simple - removed the plates that cover the end of the handel, then removed the screws and the broken handle. There were four screws - did a top one, then a bottom one, then the other top and bottom one. Made sure they were on tight and put the covers back on. Really proud of myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND FORKS, ND
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke (3rd one) poor design
replaced handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SWAMPSCOTT, MA
- Parts Used:
- 297311201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke loose
Just screwed in the new handle. Must keep the original trim pieces that slide on the top and bottom, or order new ones if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from MENDON, MI
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle
remove cover plates slide off , exposes screws holding handle on to the door remove screws ( 4) 2on top 2 on bottom replace with new handle in reverse order of disassembly slide cover plates back on , job complete .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from HIXSON, TN
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Took off 4 screws and replaced the handle. Took less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from Little Rock, AR
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just lost key
No repair. The key fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from ORLANDO, FL
- Parts Used:
- 5304507199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door wouldn’t stay shut
Purchased gasket from parts plus installed it and door still won’t stay shut without duct tape plus the frost is building up really bad looking for another parts store to get problem fixed
Was this instruction helpful to you?
Thank you for voting!
Stop basket and right side shelf support were broken.
Used needle nosed pliers to twist and pull out remainder of broken parts (regular pliers would work, fingers might). Used fingers to insert replacements. So, simple, so glad I did it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from LEXINGTON, KY
- Parts Used:
- 297311201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke off
Four screws and slip on the covers! That's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from North Little Rock, AR
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Warm out door gasket.
Had to lossen around 60 screws to allow for the old gasket to be removed. Then I began the process of inserting the new gasket by fitting it into the gasket channel opened when I loosened the 60 screws. I inserted the gasket a little at a time making sure it was properly fitted then I tightened that part and then do the next part until I finished replacing the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HARDING, PA
- Parts Used:
- 297216004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer wouldn’t turn on.
Put the new temperature control unit in plugged freezer back in and immediately turned on. Very simple repair. Saved a lot of money not having to purchase new or call a repair shop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from MANLIUS, NY
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not reaching temperature
Using the socket wrench, I removed the old element from the oven wall attached by two hexagonal screws. I then removed the electrical attachment to the oven using a Philips head screw driver. Replaced the element with the new one and reversed the process. The oven works like new!
Was this instruction helpful to you?
Thank you for voting!