FRU17G4JW7 Frigidaire Refrigerator - Instructions

remove cover plates slide off , exposes screws holding handle on to the door remove screws ( 4) 2on top 2 on bottom replace with new handle in reverse order of disassembly slide cover plates back on , job complete .

Took off 4 screws and replaced the handle. Took less than five minutes.

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Slipped off the top and bottom screw cover plates unscrewed the 4 retaining Phillips screws, removed the old handle and replaced it by reverse the procedure. The best part of the process was the amazing quick delivery and efficiency of Parts Select.

Replaced fan. I ordered the fan and received it the following.(-:

Removed upper and lower screw covers. Removed 4 screws , Removed broken handle. Installed new handle with th 4 screws provided. Replaced screw covers. Done!

Removed decorative end caps on each end of the handle just by sliding them off. Unscrewed the broken handle and used the same screws to install the new handle. Replaced the decorative end caps by sliding back in place. Entire process took less than 2 minutes.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

Even though we did not have the model or part number I was able to easily locate the exact part because of your photo, dimensions and video instructions.