FFSS2615TD4 Frigidaire Refrigerator - Instructions

The repair didn't happen. The bin arrived broken and I have been ignored by whoever takes care of getting me a replacement. I would very much appreciate some communication

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

When I went to install the new shelf, I saw two small ridges near where the shelf mounts on either end of the door. It was possible to slide the new shelf in behind the ridges, making a tighter fit for the shelf. Probably this was not done when the refrigerator was delivered and installed by the delivery person.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

Remove plastic cover from freezer door by sliding upwards and disconnect wire harness.
Disconnect wire harness from refrigerator to module.
Unscrew 3 x philips screws securing the module frame in the door.
Remove the plastic water tube from the dispenser module.
My water tube was perished and leaking, so I replaced it with 6mm diameter automotive vacuum hose and secured it to the water line spigot with a zip-tie. (Note: the module I ordered does not come with a water tube).
Re-assembly is the reverse of the above.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

Removed all contents from the glass shelf.
Lifted out the glass shelf.
Lifted out the broken plastic frame.
Set the new plastic glass shelf frame in place,
Washed the glass shelf.
Placed the clean glass shelf upon the new frame.
Replaced the removed contents onto the glass shelf.
Fini!!!

put the new ones

All you do is just put in slide down and it’s in

First I order a part from your company and it came delivered broken. I got my money back and ordered same part and asked girl to make sure they put bubble wrap so it won't brake. Delivered a second time broke again. No bubble wrap. So using my brain like I said I ordered from a different company it arrived and not broken with bubble wrap. All it was a door shelf

I took the side cover off. With a Phillips unscrewed the screw, took the outer part off, with nut driver undid the two screws. Took the part out in screwed the 4 Phillips head screws. Took out the broken part, replaced with new part. Reassembled. Put filter in and it now works perfectly.