LFSS2312TP4 Frigidaire Refrigerator - Instructions

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

The repair went easily after watching the video, took me less than an hour to complete the repair.

Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !

I bought and replaced the control board as suggested. It didn't help. It was suggested that it was the Damper [lets cold air from the freezer into the refrigerator side]. I bought a new Damper unit. It didn't help. It was suggested that I replace the temp sensor[s]. I replaced them both, and the HI alert disappeared, but it did not help with cooling the refrigerator. I gave up after spending $400 on parts with no solution; I bought a new double-door refrigerator.
Note .... None of these parts come with any instructions. You have to watch youtube.

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

Very simple installation.Gentle pull out on the old Ice Container and Auger Assembly.Take the new Ice Container and Auger Assembly and slide in place.Make sure everything is lined up.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

There was no repair needed. I broke the glass shelf that inserts to a plastic frame that holds the fruit/veggie drawer on the fridge.

I found the part very easily on the site and ordered it. The part came exactly as described on the Web site.

Installed new Auger drawer assembly

I ordered a replacement ice/water dispenser module from partselect.com using my model number. The correct color of grey was available. First, turn off power to the fridge. There are 3 number 2 phillips screws under the drip tray that mount the facing to the refrigerator. Remove those screws and gentle lift up on the facing to remove it from the slots that hold the top of it to the fridge. Unplug the cable and set the facing aside. Locate the power plug for the ice dispenser module. It should be to the left of the module. Remove the 3 screws that hold the module to the fridge and unplug. Gently pull foward to release the module from the fridge. Once it is free, push the water dispenser tube out towards the fridge doing so from the dispenser handle side until the tube frees from the old module(this is the hardest part to achieve but doable). Repeat the process in reverse to install the new module. This took me 15 minutes to remove and install the new one.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

i ordered a replacement, and when it came in i took the old part off and installed the new dispenser. it works great.

The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches