FRS28XHAB0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Cedar Park, TX
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic sidewall of drawer split
ordered new drawer, removed the clear plastic front piece from old one and installed on the new one. It was delivered only one or two days after I ordered it and was in perfect condition. Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Bullard, TX
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor design resulted in lower crisper drawer breaking on both sides.
Got the new drawer 2 days after I ordered it. Snapped the front off the old drawer and onto the new one, and slid the new drawer in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Buffalo, NY
- Parts Used:
- 5303289501, 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Sides of drawers were cracked, unable to use.
I found PartsSelect on the web, input my appliance model# and type and a very easy to read diagram of my appliance appeared. I simply selected the parts I needed from the diagram,and the part numbers were displayed. I placed my order and 2 days later the parts arrived, and I installed them immediately. No fuss, no problem. Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynne from huntington, NY
- Parts Used:
- 215162502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken rail
Removed basket to access rail...used nut driver to remove screws from exisiting rail (BE SURE TO SAVE!!!!) Lined up new rail and replaced screws.......replaced basket....SUPER SIMPLE!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from STOCKTON, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
4 broken drawer cover supports
Followed someone before me instructions. very simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from GLENDORA, CA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer colk, refrig warm
Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derekandkelsey from WINCHESTER, VA
- Parts Used:
- 3206319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Blown thermal fuse for Ice Maker
After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.
It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from ROYSE CITY, TX
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Freezer wasn't cooling - compressor not engaging
Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from State College, PA
- Parts Used:
- 5303289501, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer and rails broke due to under design of the components
This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cypress, TX
- Parts Used:
- 218215245
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer Door would not stay closed after closing refridgerator dor
1. Removed plastic cap on hinge by gently prying up on an edge and lifting up.
2. Removed 3 screws in the hinge, one at a time.
3. Removed hinge and broken piece in freezer door.
4. Installed new hinge: Ensure spring goes back into larger hole and the alignment pin is in the smaller hole.
5. Turn top of hinge and align all 3 holes.
6. Place screws in all holes and loosely tighten.
7. Align freezer door
8. Tighten all 3 screws while holding freezer door in alignment.
9. Replace plastic cap.
2. Removed 3 screws in the hinge, one at a time.
3. Removed hinge and broken piece in freezer door.
4. Installed new hinge: Ensure spring goes back into larger hole and the alignment pin is in the smaller hole.
5. Turn top of hinge and align all 3 holes.
6. Place screws in all holes and loosely tighten.
7. Align freezer door
8. Tighten all 3 screws while holding freezer door in alignment.
9. Replace plastic cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WETUMKA, OK
- Parts Used:
- 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
storage drawer frame had cracked in the back
Simple, removed old frame, took off the humidity slide control and installed on new frame. Slid it back in place. Great service, had it the next day, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WAPAKONETA, OH
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker stopped producing Ice.
After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!
Was this instruction helpful to you?
Thank you for voting!