FSC23R5DSBB Frigidaire Refrigerator - Instructions

The door clunk problem was as others described. Repair similar to others described. The major thing to understand which I didn't see listed elsewhere is whether the top or bottom little nylon toothed cam is broken. This part is the one in the door. There was also one in the hinge, PS976594 or PS430814 ? I ordered this one and was lucky that it was correct. I'm not sure whether it's possible to know whether door side or hinge side is broken, without removing the door to see.

Simply unscrewed cover on water filter and pulled old filter out. New filter comes with o-ring on filter. Simply reversed procedure and installed new filter.

My hand turned the water filter casing around until it unscrewed and then I put in the new water filter.
Screwed the casing tight and I was finished.

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

I just slipped it into place.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

No previous experience with this appliance, a 36 inch side by side unit. Had to determine how to access the area to replace the part. This is done from the front with the door closed. The bottom shelf in the dispenser area elevates and slips out. Retainer screws are then evident. Remove screws that hold trim and then unplug the electric attachment for the switches from the trim which contains the light and selection controls. Next remove the screws placed around the circuit board holder. This then allows the section attaching the ice dispenser and water dispenser to be pulled forward. Do not disconnect the water tube. Two small metal retainers for the water dispenser can then be removed (three small screws) carefully. Remove the broken part of the old actuator and place the new one in the slots. Replace the retainers (start the retainer screws by hand unless you have a magnetic screwdriver). Replace the section holding the circuit board; then the trim and the bottom shelf. Easier than anticipated.

Replaced bad parts with new parts it went easy

Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Repair man wanted a 130.00 service charge plus parts , With the help of YouTube we did the repairs inhouse , couldn't believe it was that easy. Refrigerator is working like a new one ,our maintenance crew has ice cubes were all happy !

I had a repairman here and after spending 350 dollars after 4 visits and parts, I decided to try it myself. I ordered a compressor start relay and a run capacitor. Replacement took all of 15 minutes and now runs again for the first time in a month. Thank you Parts Select. You’re the best!