Models > FGSS2335TF6 > Instructions

FGSS2335TF6 Frigidaire Refrigerator - Instructions

Jump to:

All Instructions for the FGSS2335TF6
76 - 90 of 308
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Marco Island, FL
Parts Used:
242252702
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice maker was over filling.
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from POTTSTOWN, PA
Parts Used:
EAFCBF
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER
VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from WALLING, TN
Parts Used:
241639502
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melissa from Olden, TX
Parts Used:
242252702
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from LANCASTER, KY
Parts Used:
242252702
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
LEAKED WATER AFTER USING WATER DISPENSER
DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Craig from Eastlake, OH
Parts Used:
242252702
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Fridge leaked water all over my kitchen
I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cloid from HOOVER, AL
Parts Used:
241885001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Ice Director Door Broken In Half
I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Woodrow from INDIANAPOLIS, IN
Parts Used:
241973101
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Originally part was broken
Removed the glass top, replaced on new part. Then placed back into refrigerator.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from CHAMPLIN, MN
Parts Used:
241990301
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Broken hinge bearing, refrigerator door, top bearing
1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul S Van from BRUNSWICK, ME
Parts Used:
242194301
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Trim on door water/ice dispenser broke off
Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.

About two minutes.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stefan from LAKE WORTH, FL
Parts Used:
241786015
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
No problems
Removed old gasket and installed new one by pushing the gasket in the door groove.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ville from SAN JOSE, CA
Parts Used:
8582405058065
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Ice maker doesn’t work
Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jennifer from Burnsville, MN
Parts Used:
240350613
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broke glass fridge shelf/insert while cleaning it...
There was no repair needed. I broke the glass shelf that inserts to a plastic frame that holds the fruit/veggie drawer on the fridge.

I found the part very easily on the site and ordered it. The part came exactly as described on the Web site.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from South Hamilton, MA
Parts Used:
240324502
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door bin broken.
I received the part and slid it down the molded runner and secured it.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Lockport, NY
Parts Used:
241639502
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
12 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FGSS2335TF6
76 - 90 of 308