LGHK2336TF5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dale from Fort Wayne, IN
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken crisper supports
The video was very helpfull. They were fixing the same refrigerator that I have. I punched in the set pin on the old part. Removed the old part by prying it out with a putty knife. Inserted the new part and drove in the set pin. I was glad that PartSelect had my parts. The repair shop in Fort Wayne Indiana did not even show this repair part on their computer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Pittsburg, PA
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Leaking Water Vlave
Just follow the instruction that come with the valve. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Jensen Beach, FL
- Parts Used:
- 241993101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water dispenser dripping causing corrosion below tray
Replacement of the water valve repair was a snap. Only the main supply line needed to use a nut to secure the water supply. All other lines were simply cut below the pointed end of the plastic tubing line, nylon nut discarded and simply pushed in to seat with a O-ring fitting. Took no more than 10 minutes to install the new valve and test for leaks after turning water back on. This was the easiest appliance repair I have done in > 5 years, 100% success first time,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from Barbourville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
left out in the cold an froze
remove the old one and replace with the new one and yes it was that easy. All of the lines and wiring connectors were color coded
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Sapulpa, OK
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Water began to leak from valve
We followed the online instructions and tah-dah it was working...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
Broken crisper supports
I followed the video and everything went smoothly. After pushing the pin in I pulled out the broken pin with needle nose pliers-very easy just like on the video. It took more time finding all the simple tools than the job itself-well almost!
Was this instruction helpful to you?
Thank you for voting!
Broken crisper pan guides
Nothing exciting - just replaced the defective drawer covers with the new parts. The guides are poorly designed. the bottom guides on both covers failed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lakeland, FL
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Shelf Insert shattered in my hand while I had it out cleaning it.
Simply replaced the glass shelf. Fit was finish were great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Chandler, AZ
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Drawer support was broke
Pried the broken support insert out with a screw driver and pulled it out with pliers, then inserted the new and pressed it in and Presto the drawer now works good again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGEL from ORANGE CITY, FL
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
shelf support broke
I pull out the broken part by push the center pin thru and then rerome all the parts. I then positioned the new part in place and push in the center pin to lock. quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Harpswell, ME
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker wasnt making ice
Water was leaking so I replaced the entire valve and just followed the color codes and thats it. Plug and play.
Was this instruction helpful to you?
Thank you for voting!