LFSS2612TD1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- B J from Dillingham, AK
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frost build up on evaporator
Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from HENDERSONVLLE, NC
- Parts Used:
- 242077705, 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
EVAPORATOR FAN MOTOR & BLADE
The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RANDY from NORTH CHARLESTON, SC
- Parts Used:
- 241993101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.
None of this was obvious - an online tip from another member was invaluable.
Was this instruction helpful to you?
Thank you for voting!
chrisper drawer jammed found supports were broken
Looked at video on how to remove and reinstall support and followed the instruct ions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Denver, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water dripped from water outlet on door
Replaced the Triple Water Valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Hot Springs Village, AR
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
When washing the shelf insert glass piece, it broke into a million pieces.
The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Ocala, FL
- Parts Used:
- 240334201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One arm on the plastic bin or tray cracked and broke.
This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from BELLE HAVEN, VA
- Parts Used:
- 240350702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
THE CRISPERD DRAWER SLIDE WAS BROKEN.
REMOVED THE DRAWER, LIFTED OFF THE GLASS, REMOVED THE BROKEN SLIDE, AND PLACED THE NEW SLIDE IN THE PROPER SPACE. REPLCED THE GLASS SHELF TOP AND THE DRAWER. PEICE OF CAKE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from NORTH DIGHTON, MA
- Parts Used:
- 242126602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
pushed bin into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from ORANGEBURG, SC
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
both bulbs blown out
unplug refrigerator and insert the bulb in refrigerator first and then insert the second bulb in freezer side. After which, plug the refrigerator back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from KILLEEN, TX
- Parts Used:
- 240356402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I drop a Ketchup bottle on the corner of the bin
Glue the old one with gorilla glue. Made space and put the bin in. Now I have an extra one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from MT PLEASANT, SC
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Remove old shelf and replace new
Slip out old shelf, remove glass and clean, slip in the new shelf and replace glass on top. That easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from CHICAGO, IL
- Parts Used:
- 242126602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidentally dropped a bottle and cracked the bottom bin of our refrigerator.
Once I received the new bin, I removed from the box, then took it out of the plastic wrapping and gently placed on the door of my refrigerator. It was THAT simple. I honestly expected to do more work. I was pleasantly surprised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from CYPRESS, TX
- Parts Used:
- 242126602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the Bin-Door
Replaced said Bin-Door.
Was this instruction helpful to you?
Thank you for voting!