FGSS2635TP6 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Samuel from KILLEEN, TX
- Parts Used:
- 240356402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I drop a Ketchup bottle on the corner of the bin
Glue the old one with gorilla glue. Made space and put the bin in. Now I have an extra one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shellie from MONCKS CORNER, SC
- Parts Used:
- 241786014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Freezer started icing up. Gasket was torn in places letting air in.
The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Detroit, MI
- Parts Used:
- 241786014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer door gasket became loose
Followed instructions for this part from this site and things went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from TONEY, AL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
ice maker would not dispense cubes, stuck on crushed ice
turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SOCIAL CIRCLE, GA
- Parts Used:
- 242126602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the shelf in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ellsworth, WI
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker line was freezing
Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Seneca, NY
- Parts Used:
- 241993101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken shelf support
I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tess from San Diego, CA
- Parts Used:
- 240351602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing freezer bin
just put right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FERDINAND from AURORA, CO
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was cleaning the refrigerator and I accidentally dropped the insert
I just slipped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from buffalo, NY
- Parts Used:
- 242126602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked bin
Inserted unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory L from LAS VEGAS, NV
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame had cracked from weight of items nd age of frame.
Removed all items from glass top then removed drawer from frame. Removed damaged frame. Transferred glass top to new frame and installed new frame. Reinserted drawer. E Z P Z
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Chesapeake, VA
- Parts Used:
- 241969501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken frame
removed broken one and slid in new one, put in glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HILLIARD, OH
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame of meat drawer cracked
Took out old frame by removing drawer then lifted frame out. Lifted glass panel out of frame, place glass panel in new frame, places frame back in refrigerator and slid drawer back in. Easiest repair ever and I repair nothing myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CULPEPER, VA
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame around deli drawer cracked
Removed and inserted new. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!