FFHB2750TD2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MICHAEL from STATEN ISLAND, NY
- Parts Used:
- 5304537408
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer was causing frost and ice
i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GRAY, ME
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was torn and leaking cold air causing condensation and water dripping when door was opened.
I pulled the old one out and pushed the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from WEST DEPTFORD, NJ
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not making ice and leaking water from aebecause the icemold in the ice maker cracked
Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from MACOMB, MI
- Parts Used:
- 242270106
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The funnel guide cracked and the spring that stops ice and water stopped working
The diagram on the frigidaire website said 4 screws and 3 wires to disconnect and part comes out and reverse the steps for install actually took less then 5 mins...easiest and first repair I have done and the part was 20 bucks cheaper at parts select then anywhere else on the internet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from ROCHESTER, NY
- Parts Used:
- 242270106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water and ice dispenser would not shut off automatically
Unscrewed the 4 screws that hold the dispenser in place. Disconnected the wiring harness from the old dispenser.
Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.
Works like a charm!
Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.
Works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from LANCASTER, CA
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No water to the ice maker or water tap.
Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsay from HUNTINGTN BCH, CA
- Parts Used:
- 242071301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door shelf broke
Snapped the new shelf in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from AKRON, OH
- Parts Used:
- 809069206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
condenser fan is no longer holding running speed
Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from FAYETTEVILLE, NC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Torn Freezer Drawer Gasket
Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Brookfield, CT
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator wasn't staying cool enough
Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!