LGHT1837NF5 Frigidaire Refrigerator - Instructions

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.

Just removed the broken pan and installed the new one within 2 minutes. Really simple

The old support just unscrewed & then the new one screwed right on with two screws.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

I ordered a freezer gasket/insulation lining; just pulled the old one out and put in pressed in the new one; solved the problem easily. Then the refrigerator gasket was falling apart. I was ready to buy a new refrigerator but then I got laid off from work. I ordered the 2nd gasket. It did not fit easily at all. My husband had to man-handle and stretch it; then it worked, as worked well ever since. Spent $250 instead of $1250+. Thanks. P.S. Could not find the year of the frig.

Took off old part and installed new part

Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)

I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.

Twisted replacement bulb into place easily. Let there be light!

The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.

Replaced thermostat and defrost timer and still freezer to warm.
After research with U-tube video of (Fixin it with Pappy) discovered that my fridge has one thermostat in fridge section and in cold months (live in ohio)the garage is cold therefore themostat in fridge does"nt need to tell the compressor to kick on. Pappy is a retired engineer and in very easy to follow instructions will show you how to fix this problem. Strongly suggest to search for his video on Utube. I did as he instructed and my fridge freezer works great in cold weather now. Its apparent to me I wasted my money on the parts. I didn't` need to replace. Just happy my Beer fridge is working all seasons now.
John from Ohio

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

No big deal. Placed the order, got the replacement. Put them in and that was that! The great thing is, I have a perfect refrigerator for new renters. It would have been a lost rent without these easy to get parts. Thank you.