FGSS2635TP8 Frigidaire Refrigerator - Instructions

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

First I order a part from your company and it came delivered broken. I got my money back and ordered same part and asked girl to make sure they put bubble wrap so it won't brake. Delivered a second time broke again. No bubble wrap. So using my brain like I said I ordered from a different company it arrived and not broken with bubble wrap. All it was a door shelf

All you do is just put in slide down and it’s in

Removed all contents from the glass shelf.
Lifted out the glass shelf.
Lifted out the broken plastic frame.
Set the new plastic glass shelf frame in place,
Washed the glass shelf.
Placed the clean glass shelf upon the new frame.
Replaced the removed contents onto the glass shelf.
Fini!!!

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Pulled from box snapped into place took just a minute

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Went to oartselect.com located diagram and part. Took out ice drawer to prevent ice being dispensed. Remove small front panel in door for ice- water & cubes, 2 square tip screws on top. Remove small grey panel, 2 Philips head screws, remove ice dispenser unit 2 Philips screws, unplug 1 wire connector.
Insert ice dispenser unit from partselect.com, connect wire connector, screw in 2 Philips head screws, place cover panel in position and screw in 2 Philips head screws, place small grey panel in position and screw in 2 square tip screws. Put ice drawer tray back in refrigerator, try water, try crushed ice, try cubes. FINISHED, just saved yourself a couple of hundred dollars in less than an hour. My wife said she could do it after watching how easy it was.

Slid the meat pan out of the fridge, popped the glass from under and removed it, popped the front of shelf upward and then slid it out, and for the new one I did everything in reverse that’s it took me less than 10 minuets.

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

First: I could not watch any videos. Big downer. Read the reviews and read a post about “three screws”.
Opened the freezer and emptied everything in it.
Remove the bin.
Two screws are on the left side. They go into the side wall.
Here’s where things get weird. The plastic “box” holds the “ice making assembly”. That box is attached by FOUR slots. You will need to remove the wire rack below the frame. There’s a plastic spacer on the left side with a slot on it. You can pull it of with your fingers when you rotate it. Slide the rack to the left and pull down the rack from the RIGHT side holes. You have move the box toward you about a inch, then it drops down.
Now, there is a electrical connection from the box to the rear of the refrigerator wall. You need a small screwdriver to lift the tab on the TOP of the connector to release it. Once that is done, slide the box forward and put it in the sink.
While all this is happening, the freezer is thawing out.
Once you remove the box, you will get error codes on the digital display. This is a good thing.
There are two “square head’” screws that you have to remove to separate the TWO parts that make the box. Slide the outer trim towards you.
The icemaker assembly slides into four slots. You put the new wires in the same place as the one you removed.
Put everything back together the opposite of the removal.
Now for the secret.
All that food you removed? Put it back in until you can slide the box into place.
Then you plug the connector in. The box should be sitting on the food.
THIS IS THE SECRET.
The ice maker has two options. Cubed or Crushed.
There are two components that make them happen. On the left side there is a slot with a gray lever the moves up an down. There is an piece of aluminum on the right side the drives the screw in the box.
Rotate the screw drive to 45 degrees.
THIS IS THE SECRET.
On the left side of the box is a rod that is spring loaded and has a bent end.
It’s about “timing”.
Find a piece of “kite string”. I used the string from the yellow energy tag that came with the fridge.
The box is sitting on the frozen food. The wire in the back is connected.
Loop the string around the lever AND PULL UP.
Slide the whole thing into place using the slots.
When it’s in place, let go of the string.
Put the two screws back in.

FINAL.
You have to PRESS AND HOLD the IceMaker button to reset. You’ll get ice cubes in a couple of hours. Through the first 24 hrs away.
You’re welcom.

Well I’ve been cleaning refrigerators for 50 years... so have experience removing shelves etc., for cleaning....I removed shelf and then glass and put new one in........easy peasy

I ordered a new shelf and I put in, less than minute