LGHB2869TF7 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from ROUND TOP, NY
- Parts Used:
- 5304508067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Left guide wheel broke off on both drawer covers definitely a design problem
Replace the drawer cover by removing the drawer brackets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from MACOMB, MI
- Parts Used:
- 242270106
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The funnel guide cracked and the spring that stops ice and water stopped working
The diagram on the frigidaire website said 4 screws and 3 wires to disconnect and part comes out and reverse the steps for install actually took less then 5 mins...easiest and first repair I have done and the part was 20 bucks cheaper at parts select then anywhere else on the internet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from ROCHESTER, NY
- Parts Used:
- 242270106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water and ice dispenser would not shut off automatically
Unscrewed the 4 screws that hold the dispenser in place. Disconnected the wiring harness from the old dispenser.
Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.
Works like a charm!
Reconnected the wiring harness to the new dispenser.
screwed in the 4 screws that were removed.
Works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GRAY, ME
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was torn and leaking cold air causing condensation and water dripping when door was opened.
I pulled the old one out and pushed the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from WEST DEPTFORD, NJ
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not making ice and leaking water from aebecause the icemold in the ice maker cracked
Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorena from HOQUIAM, WA
- Parts Used:
- 242071301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a broken bin on one of the doors.
We just slide in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from LANCASTER, CA
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No water to the ice maker or water tap.
Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from KATY, TX
- Parts Used:
- 5304512616, 5304508034, 5304508033, 5304508016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The wheels on the glass drawer, as well as the vegetable drawer broke.
I ordered a new vegetable drawer, glass shelf and 2 additional wheels. I removed the metal frame from the glass shelf, and placed them on the new shelf. I then replaced the broken wheels (gliders). The whole process took less than 20 minutes. The parts fit perfectly! I have to commend this site in helping me figure out exactly what I needed, since I originally ordered the wrong part, but they walked me through the correct ordering process and made the return of the incorrect very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsay from HUNTINGTN BCH, CA
- Parts Used:
- 242071301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door shelf broke
Snapped the new shelf in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul S Van from BRUNSWICK, ME
- Parts Used:
- 242194301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Trim on door water/ice dispenser broke off
Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.
About two minutes.
About two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from AKRON, OH
- Parts Used:
- 809069206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
condenser fan is no longer holding running speed
Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Was this instruction helpful to you?
Thank you for voting!