FGSS2335TF1 Frigidaire Refrigerator - Instructions

Removed a few screws from the front panel and unplugged the wire harnesses. Pulled the old module out and put in the new one in. It was super simple and fixed the problem.

Just popped the new bin into place with my thumb. I also wanted to say. . . Don't bother with express or overnight delivery. I ordered the new bin on a thursday, paid for 3-5 day delivery and it arrived the next day. Installed it in less time than it took me to unwrap it.

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

Had to replace with a whole new part, had to take it all apart to replace

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Basically unhooked water lines and removed the screws

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

very easy, make sure to watch the provided you tube video.

Followed instructions in video that was suggested when I placed the order.

i watched the video very simple repair

I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

carefully removed retainer from old valve

The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!

First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.