FPCI21TFW0 Frigidaire Refrigerator - Instructions

Since the end caps were already broken I just took them out & put the new ones in. Total time to do this was less than 5 minutes. Great parts, great prices & super fast shipping

Just snapped in the wholes and pushed it down a little bit and there it was. It only took 2 minutes. Very simple process- price was supper and delivery was very fast.
Thanks guys- will order from you again

Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinstall the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.

There were about 30 or so hex head screws holding the interior panel to the door; best to use a power hex head driver. Removed the gasket from the old panel, put the gasket on the new one and reversed the process (there were about a dozen less screw holes on the new panel). Went without a single hitch in less than an hour!

Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.

The plastic ends that held the shelf on broke off, once my new ends came in the mail I had to attach them to the metal bar that holds the condiments in the door's shelf. To do this I had to hammer the ends of the shelf a little to get the caps to fit. Once they were on I put the ends of the caps into the holes on the door and had to push down with some force to get them to snap in. Very easy once I realized I had to push harder than I expected to get them to snap in. It's great to have my shelf back!

Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.

Put glass in the new crisper cover and the support bar in place.

replaced it

Cleaned insert hole, did a dry-run, then pressed everything permanently in place.

I flew up to Sacramento to help my Aunt with chores around her home & saw an end cap was missing in her refrigerator so I ordered the part from you kind folks & had it sent to her I think she figured it out & is very happy .

This past February 6th, my wife and baby son were in a car accident. Friends were generous and brought food for my family during the height of our crisis time. Our refrigerator was very full and the bar across the door shelf got pushed in and the end caps broke. We ordered the end caps (with the excellent help of Susan M. in customer service) and recieved the parts the next day. I fitted the parts on to the end of the bar and firmly snapped them into place in the refrigerator door. Done! It was that simple. The hardest part was getting both the left and right part, and Susan M. wen WAY out of her way to help us in our time of need. It may sound like a small thing, but it was one more problem during a time of significant family stress and hardship and it was one of the very easiest to fix and it was all done very very quickly. Thank you PartSelect and thank you Susan M. You were our angel in a time of need.

The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.

the parts fit good but tight. I needed to tap them in place and everything worked good. Your shipping is very fast and you had the parts!!!!!