FRS23KF6DW2 Frigidaire Refrigerator - Instructions

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!

Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.

Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 15 mins

First I removed the plastic drip pan that catches the ice and water. There were two or three screws that had to be removed. Next I removed the old broken actuator and put the new one in. There were two more screws to be removed to replace the old actuator. Those screws were pretty small and hard to get out. Other than that, the new actuator went right in and was working in no time. Overall a pretty easy project.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!

Replaced an evaporator motor which had previouly been put in to replace original with an alternative which changed the original electrical connectors. Had to replace those replacements witn originals which extended the changeover.
Now works like the original and very quiet because your motor fit in the original rubber bushings. The alternative motor was put in by the Frigidaire repair man and at considerable expense because the warrenty date had been exceeded by one month.

I simply unscrewed the original and replaced it with the replacement. It was very easy. I did have to order the label as the original one would not come off to be re-used. Hopefully, that will go on easily as well.