FPGS19TSL0 Frigidaire Refrigerator - Instructions

I found this website via a google search and clicked on the link suggesting solutions for the symptoms I had. I decided to order the part (defrost timer) that was proven the larger percentage of time to fix my issue (warm refrigerator) but decided to also purchase the evaporator fan motor as it was suggested by my brother to replace it as well. We powered off the refrigerator and removed the back wall of the freezer and completely defrosted the unit. This seemed to be the most work and longest time to complete. We used a hair dryer to do this. Once the ice was gone, we replaced the defrost timer, which seemed to fix the warm refrigerator part. We didn't immediately swap out the evaporator fan as the power plugs did not connect properly and it was a little confusing on how to accomplish this. I called partselect back and they didn't have anyone that could talk to me throught the replacement process but recommended we call frigidaire. Meanwhile, we found out that the defrost timer corrected the warm refrigerator and now that the evaporator fan could move (no longer frozen in ice) it was making a lot of noise. So we contacted fridgidaire, and they were able to provide me with a similar video on connecting the power between the new evaporator fan motor and the refrigerator. . We ended up snipping both power connectors (from fridge and new part) and twisted the wires togehter and now the fan is moving without noise, the freezeer and refrigerator is working like a champ! Very happy outcome!

Removed shelving, and rear panels. Replaced condenser fan and defrost thermostat. Defrost coil ohmed fine. Reassembled and plugged in fridge with thermometers inside. Freezer at 22degrees and fridge at 32 degrees. My first time repairing a fridge. the partselect videos were very helpful.

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.

This is a top and bottom frige. I unplugged the fridge and I took off the sheld in the freezer and removed the blower fan cover and unplugged the fan to remove the back freezer panel. Be careful when moving the fan. It looks sensitive. I used a hair dryer to melt the frost to get to the screws. Because it was frosted the back panel was hard to take off. Don't force it too much, just keep melting the ice. Once it was off the radiator looking thing was completely frosted and iced over and I couldnt even see the thermostat. I started blowing it with the hair dryer and it started melting. It took an hour to get the ice melted enough to actually see and remove the thermostat. You may want to leave the fridge off for a day. I didnt have a choice because I didnt have anywhere else to place the food. I was using the freezer as the fridge. Thats how cool the freezer was. I cut the wires for the thermostat. Im sure you could check which is positive and which is negative. I just looked at the direction the wires went. This works but it is not guaranteed. Check for ground. Google it if you need to know how. I used the clamp connector things but I didnt have a clamper so I used a plier. It works but I didnt like how it clamped. The little tubing didnt work for me becuase I didnt have a solder gun to warm it up and using a match is not good. You'll burn the wire. Buy electric tape and wrap it around. Dont use regular tape. Go to home depot it costs 99 cents. Make sure all ice is melted. Go over everything with the hairdryer to melt the ice. You dont want it to start freezing and clog up the vents, expsecially the one that goes from the fan to the fridge. Before I put everything back together I changed the defrost timer because I figured its best to change it since you never know. I loosened the two screws but first I took offf the screw holding the timer panel. I changed the defrost timer and connected it back. Then I screwed everything together. Then I screwed in the back freezer panel but not the fan cover so I could see if the fan is working. I plugged in the fridge and the fan didnt work. If you look under the defrost timer panel, the timer has a round part that you can move with a flathead screwdriver. Move it lightly clockwise and the fan will start. I read that the fan goes for 8 hours and then it turns off for a half hour. Seems like a lot of time to be on but its been a week and the fridge and freezer are working real good. This website is good and the aprts are cheaper than Sears.

First I removed the inner door which was easy and used a drill with a hex head driver to undo all of the screws behind the gasket. Trying to fit the new gasket on was a fidely nightmare. It's not too bad to get the sides on but the corners are very difficult. At first I had left the door on the fridge after an hours worth of swearing I took the door right off and laid it flat on a table. When I finally got the gasket all on, with a couple od small tears, I hit it with a heat gun and got most but not all of the wrinkels out. When I put the door back on the fridge it wouldn't close properly - gaps in the gasket. I leaned some weights against the door and it the gasket with the heat gun again. Gradually over 2 days it fit fairley well.

I followed the advice of many people with the same problem, and replaced the Defrost Thermostat and Defrost Timer. Both repairs were relatively easy, and the problem appears to be solved. The replacement of the Defrost Timer is very easy (about 30 minutes), and I wish I had stopped at that step and waited 48 hours to see if that fixed the problem. But, I wanted to replace both parts that I had purchased - - In my refrigerator, access to the Defrost Thermostat is through the back of the freezer panel. Not too difficult to get to the area, but I had a bit of a problem in replacing the part, and might have been better-off to see if step 1 fixed the issue. The problem that I ran into is that I don't have a crimping tool, and crushed both of the connecting sleeves when trying to 'crimp' them with a set of wire-strippers. Rather than to invest in a crimping tool, I connected the wires and sealed with electrical tape - - Now that the issue is resolved, I will likely re-open and use a proper connecting sleeve (with a proper crimping tool). My advice is to buy both parts, and replace just the Defrost Timer first. Chances are good that it may fix your problem, and you are only out $20 for the second part, which you can leave in your junk drawer until you may need it some day! All in all, it was a great way to spend $40 and avoid a costly service call!

Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.

bottom left cornerof fridge defrost timer replaced two bolts and a wire

The repair was straightfoward. The evaporator motor I received from partselect was a different model with different wiring configurations. I cut the wires from the new motor per the instructions I received with the new motor and I did the same with the wires that connect to the fridge. Once I matched the wires and secured them with electrical caps I began to put the evaporator motor to the base and started screwing the screws the way I took them off. Once I connected the wire harness to the back of the freezer and turned it on I noticed a big difference in air flow. I was surprised at how easy it was to fix my refrigirator problem. It's been a few weeks now and the fridge is cold and working like it should. Don't be afraid of this task. it's very easy and will save you a ton of money. Thanks partselect.

Instructions from partselect were very clear and probable cause made it easy to narrow things down. I have the manual for the refrigerator that shows the location of the defrost timer. Very surprised that it turned out to be a cheap and easy fix.

After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

1. Disconnected electrical. 2. Removed upper console in refrigerator by removing 2 nuts. 3. Disconnected wiring from console. 4. Removed 2 screws from defroster timer part and pulled off from connector. 5. Replaced with new defroster timer and put everything back together. Thank you Steve for the U-Tube step by step video.

I watched the video online where it described the troubleshooting tips for this type of symptom. So I knew exactly what the problem was which is the defrost timer. After the part came in I just unscrewed (4 screws) the box which houses the thermostat and the defrost timer from top ceiling of the refrigerator section. Then I just unscrewed and unhooked the old defrost timer and replaced it with the new one. After finishing the installation I turned the fridge on. At first nothing happened. So I turned the dial on the defrost timer with a flathead screw until it clicked and the fridge came alive. I waited for an hour or so. The cooling cycle completed and the fridge stopped as expected. When I opened the door I noticed the interior is much colder than before and right after closing the door the fridge hummed back into life again. So I know my fridge is working again. Thanks to PartSelect for providing the right part for my refrigerator. I will definitely buy from them again if anything goes wrong.