TT18DKXRQ01 Estate Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Crete, IL
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water fill tube 90 fitting broke
Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morrie from Gillette, WY
- Parts Used:
- WP2210047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken cover
I live in Alaska, my son called me from Wyoming and gave me the Model number, I ordered the part and had it shipped to him. Saved twelve bucks over all. And got it there faster than the local appliance store..
In and out in 5 minutes.
In and out in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ft. Lauderdale, FL
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cracked Icemaker Water Fill Tube
The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madonna from Washington, NJ
- Parts Used:
- WP2166037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lost hinge to door while moving
Just put the hinge on and screwed on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from IRVINGTON, AL
- Parts Used:
- WP2156003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Refrigerator door retainer
This job was extremely easy, snap on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
replace door holder parts
doesn't need instructions, join a couple of parts together that all it was a bar to hold things in place on the freezer part door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from WARWICK, NY
- Parts Used:
- WPW10188389
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Freezer worked but the refrigerator was not cooling
Toddler left the fridge door open for an undocumented amount of time. The freezer was operating perfectly but the refrigerator was not cooling. After some research I ordered the part needed and went to work. Process was simple, just keep track of the fans mounting bracket. I installed it upside down and the holes didn't align with the back wall freezer cover.
Step 1: Unplug the fridge
Step 2: Gloves and safety goggles
Step 3: Tools - Socket Set and screw drivers. Hammer and chisel for the ice build up.
Step 4: Remove the back wall of the freezer carefully
Step 5: Remove fan and motor housing, unplug Hot, Neutral and ground wire from motor
Step 6: Drink a beverage
Step 7: Remove fan and motor from housing. You will have to reuse the rubber gaskets/washers so do not dispose.
Step 8: Install new motor and connect the hot, neutral and ground. Do not overtighten the screws connecting the motor housing to the mounting bracket.
Step 9: Before mounting the bracket, plug in the fridge to confirm the fan is operating.
Step 10: Put everything back and have another beverage.
Step 1: Unplug the fridge
Step 2: Gloves and safety goggles
Step 3: Tools - Socket Set and screw drivers. Hammer and chisel for the ice build up.
Step 4: Remove the back wall of the freezer carefully
Step 5: Remove fan and motor housing, unplug Hot, Neutral and ground wire from motor
Step 6: Drink a beverage
Step 7: Remove fan and motor from housing. You will have to reuse the rubber gaskets/washers so do not dispose.
Step 8: Install new motor and connect the hot, neutral and ground. Do not overtighten the screws connecting the motor housing to the mounting bracket.
Step 9: Before mounting the bracket, plug in the fridge to confirm the fan is operating.
Step 10: Put everything back and have another beverage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delmanda from Jupiter, FL
- Parts Used:
- WP4387490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Freezer was cooling but refridgerator was not
The evaporator coil was fully coated with ice. When all the ice melted the 2 leads on the old defrost thermostat (which was defective -- the gel was protruding over the top of the thermostat) were cut and the old thermostat removed. The leads from the new thermostat (bought from PartSelect) were re-attached to the wires that were previously cut and the defrost thermostat snapped back onto the evaporator coil.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from galena, KS
- Parts Used:
- WP2214067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Overload was open
New part was similar, except contact blade was for a full 1/4", my model utilizes 1/8". So I cut the blade in half with a hacksaw, filed off the rough edges and reassemblied the connector; attached it to the compressor
Now being a retired electronic engineer; who's great idea was it to hide a klixon inside the connector?
Now being a retired electronic engineer; who's great idea was it to hide a klixon inside the connector?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!