EI23BC30KB3 Electrolux Refrigerator - Instructions

Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover

Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

I was able to take away the trim covering the parts with a nutdriver. The base was disconnected using a phillips head screwdriver. The only real issue was how to disconnect the plastic water lines from the old base and connect them to the new one. I finally realized I just had to cut the lines where they entered the filter base because they would not pull out. I then finally understood that to install them into the new base I just had to push them in securely. The lines were long enough to do this but probably would not be long enough to install another filter base. In that event I do not know what all would have to be done. The leak had been going on for years (it only leaked when water was running to the ice machine or water dispenser). It is great having it repaired and we hope to get quite a few more years out of this old fridge.

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.