EI23BC60KS4A Electrolux Refrigerator - Instructions

I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

found the coil to be frozen like a block of ice. defrosted same, then looked up what defrost thermastat i needed and once it was received, i took the back of the freezer compartment off again, (two hex nuts, one on each end, and a small screwdriver to remove guard around fan. once this was removed, you then remove this panel, and you will see the evaperator coil, which will be frozen like a block of ice like i said. then remove defrost therm(small round piece with two wires connected to unit, disengage and re engage new thermostat. then put unit back!. no more freeze ups.also, therm was on top right of evaPERATOR. IT also snaps off on the bottom of thermastat. (just pull to or away from you and it should come off.