EI23CS65KS3A Electrolux Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rene from DIAMOND BAR, CA
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
LEAKING WATER valve
very easy, make sure to watch the provided you tube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from HALLAM, NE
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
During cross country move, water valve froze and broke.
Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from FONDA, NY
- Parts Used:
- 241547902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No light in fridge
I first ordered the wrong switch I called and got a return label and was refunded my money before even shipping the wrong switch I was helped for the right switch and it arrived in 5 days the replacement works perfectly very easy to install. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PIKE ROAD, AL
- Parts Used:
- 241691701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Limit arm on new icemaker hitting old ice cream shelf thus causing ice to overflow.
Removed old shelf and replaced with new shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ruth from vancouver, WA
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
ice maker not making ice
The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from BRIDGEPORT, NE
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Installation of Frigidaire Housing crusher assy.
I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SEMINOLE, OK
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
refrig.freezing up.
I followed the instruction video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from DUCK RIVER, TN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water line retainer missing in one port of new valve
carefully removed retainer from old valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from AIKEN, SC
- Parts Used:
- 241684503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice was not allowed to be dispensed because of worn part on auger.
Followed instructions in video that was suggested when I placed the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from WEIRTON, WV
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Plastic gate to redirect ice to the crusher broken off
Removed ice maker bin...removed screws and housing and reinstalled all...very easily completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wes from FARMINGTON, NM
- Parts Used:
- 5303918214
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refridgerator too cold...freezing food,could not turn down
First,read "how to" on the internet because the thermostat comes with no instructions and unplug refer. Second, remove food and lower rear panel. Third, pull off thermostat from tube it clips to, unhook wire harness,and cut wires.Fourth,add heat shrink tubing from store(that supplied is way too big) and connect wires with automotive connectors;shrink-seal tubing with flame.Fifth, re-install everything, and replace food.Sixth,use a thermometer to check temp and adjust controls as needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PFLUGERVILLE, TX
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Glass was broken
Took the glass out of the shipping box and it just slid right in. It was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from Langhorne, PA
- Parts Used:
- 241885001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Freezer leaked, no water disp. & Crusher didnt crush
First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirly from FRAZIER PARK, CA
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
cold freezer warm refridgetor
removed lower panel in freezer, sniped off old defrost thermostat.
Spliced in new part. reconnected power and it's up and running.
Spliced in new part. reconnected power and it's up and running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from PADUCAH, KY
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ice maker stoped crushing ice
i watched the video very simple repair
Was this instruction helpful to you?
Thank you for voting!