EW23CS75QS0 Electrolux Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Lehman, PA
- Parts Used:
- 5303918344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The icemaker was making a clicking noise. The paddle that moves to let the ice drop into the ice container had trouble moving the new ice so it could retract.
This was one of the easiest repairs I ever did. All that is needed is a nut driver. Turn off the freezer. Remove the ice container. The two screws that hold the ice maker only have to be loosened since the mounting holes are keyhole shaped. Loosen the screws, slide the icemaker up, unplug it, and remove it. Plug the new one in, place it over the scews, drop it in place and tighten the screws. Replace the ice container. Turn on the freezer. Turn on the ice maker, run it through a cycle, and job is complete. Took about five minutes, start to finish. The water doesn't have to be turned off since there is no direct connection to the ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from BRIDGEPORT, NE
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Installation of Frigidaire Housing crusher assy.
I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from AIKEN, SC
- Parts Used:
- 241684503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice was not allowed to be dispensed because of worn part on auger.
Followed instructions in video that was suggested when I placed the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAVAUGHN from MIAMI, FL
- Parts Used:
- 5304512686
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Installed new inverter
Secured bracket. Attached electrical contact to the compressor. Secured inverter to bracket.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Sapulpa, OK
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Water began to leak from valve
We followed the online instructions and tah-dah it was working...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from HUNTINGTON, IN
- Parts Used:
- 240396002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Filter would not seat without releasing itself.
Following previous installation instructions was very useful. Would add that the nut driver needs to be 1/4 in and to release the water lines from the valve body, simply squeeze the blue ring toward the valve and pull on the water lines at the same time. Simple fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Pittsburg, PA
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Leaking Water Vlave
Just follow the instruction that come with the valve. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from Barbourville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
left out in the cold an froze
remove the old one and replace with the new one and yes it was that easy. All of the lines and wiring connectors were color coded
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lakeland, FL
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Shelf Insert shattered in my hand while I had it out cleaning it.
Simply replaced the glass shelf. Fit was finish were great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon from Mission Viejo, CA
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker failed to make ice
Removed lower cardboard cover, shut off water supply valve, unpluged frig. Used wrench to remove 3/8 water line from water valve, removed electrical connectors from solenoids, used fingers to unscrew water connections from valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Canton, OH
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wate valve was leaking water
took existing water valve loose, removed plastic water lines and reinstalled on new valve and installed new valve into refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Victor, ID
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water valve went out
Very easy repair, instruction were clear and easy to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Delray Beach, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Not making ice
Simple, I had a repair man come over and diagnose the problem. After confirming, I ordered the part and replaced it. Need to make sure you get the ice build up out of the fitting tnat goes from the back of the fridge connection at the top and the filler tube inside the unit, mine was iced over. Repair man wanted to charge me $250.00... with his service call and buying the part, it cost $120
Was this instruction helpful to you?
Thank you for voting!