EW23CS75QS1 Electrolux Refrigerator - Instructions

Simple, I had a repair man come over and diagnose the problem. After confirming, I ordered the part and replaced it. Need to make sure you get the ice build up out of the fitting tnat goes from the back of the fridge connection at the top and the filler tube inside the unit, mine was iced over. Repair man wanted to charge me $250.00... with his service call and buying the part, it cost $120

This is an easy repair. Unplug appliance. Remove the old water valve by unscrewing it from the frame of the refrigerator. Disconnect the cables and all the water hoses. The hose fittings are a different type: clip off the old connectors from the hose ends and push the hoses straight into the new connectors till they fit solidly. Reconnect the cables and screw the valve back onto the frame of the refrigerator.
Unfortunately, my leak was from a hose, not the valve, so this didn't actually fix it.

took existing water valve loose, removed plastic water lines and reinstalled on new valve and installed new valve into refrigerator

took the back off refridgerator, disconnected water valve assembly, then disconnected water lines and electrcal connectors. also i received the part in less than 24 hours

Simply laid the replacement shelf carefully in the space above the bin. Nothing much to the 'repair' but I do want to say that partselect will be my 'go to' any time I need appliance parts. I ordered my shelf late on Friday night and it was delivered to my home on Tuesday! Had I ordered during normal business hours on a regular weekday I wouldn't be surprised if it arrived the next day! That is incredible and exceptional service! Don't find that very often these days.

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

My repair was a simple as logging on to the "PartSelect.com" website - very easy to find the specific part I needed. The website makes the part selection a breeze.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

(0) UNPLUG FROM ELECTRICAL POWER BEFORE ANY WORK IS PERFORMED. (1) Remove trim plate: Use fingernails to evenly pry up. It is only held in by plastic tabs, so be careful not to bend while removing the trim plate. (2) Remove touch module: Remove two black Phillips head screws, then release wire connectors on backside of control module, lift and remove module. Remove cup shield by removing Phillip head screws. (3) Remove water/ice dispensing module: Remove water filler tube from plastic clips (note: tube is installed with end slightly lower than module and there is a notch to the left side of module where the tube is routed and held in place behind module). Remove two Phillip head screws and remove module. ****INSTALL NEW MODULE AND ALL PARTS IN REVERSE ORDER****PLUG REFRIGERATOR IN TO ELECTRICAL SOURCE AFTER ALL PARTS ARE INSTALLED

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings