EI26SS30JS6A Electrolux Refrigerator - Instructions

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

Repair man wanted a 130.00 service charge plus parts , With the help of YouTube we did the repairs inhouse , couldn't believe it was that easy. Refrigerator is working like a new one ,our maintenance crew has ice cubes were all happy !

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

I got the part, hitched it up and it started working right away it fit in easily, and the directions were easy to follow thank you

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

PURCHASE:
Buy the terminator from the site because they sell the
terminator (thermostat) separately. Other places have it with the
wiring harness for more money. Changing it with the harness attached
is a very, very involved project. It includes removing the entire inner
liner of the freezer. The one the site sells requires only a simple
crimp splice and shrink tube.

TEST- If you have another freezer, ice or a friend's freezer available,
it is highly recommended that the new part be tested:
You will need an Ohm meter or a continuity tester. You can make one
very easily per instructions found on line.
TEST RESULTS-
a) At room temperature. An Ohm meter should show "Open".
b) After being in a freezer or submerged in ice water for at least an
hour, the Ohm meter should show "Closed".

I have installed hundreds of defrost thermostats. Very occasionally
one is defective. This project is a bit involved, so it is wise to pre-test.

HOW TO INSTALL THE DEFROST TERMINATOR (THERMOSTAT):
A) Prep
Remove Food & Be sure the freezer is warm.
Parts need to be pried upon & cold plastic breaks easily.
Tip: Put the screws in separate cups with labels. This will make
re-installing the many components easier.
Gather tools from the attached list.

B) Unplug Unit (Turning it off is not sufficient protection against shock.)

C) Remove Light Bulb (If it gets broken while working, glass may
get in the eyes.)

D) Remove Drawers (This is a bottom freezer unit with 2 drawers)
1) ) Upper Drawer:
a) Locate the 2 rectangular boxes covering the gears. They are
on each side, toward the rear of the drawer.
b) With a nylon spudger, push in the 2 clips on each box and
lift the boxes 1/4". They will stop at 1/4".
c) At the front of each track, remove 2 hex head screws with a
5/15" nut driver or a 1/4" flat bladed screwdriver.
d) Lift the front of the drawer a small amount while pulling drawer.
Lifting allows the 2 stops on the drawer to clear the track tabs.
e) When near the end of the drawer, lift the gear wheels slightly
to clear the track.
f) Put the drawer out of the way.

2) Lower Drawer With Front Door
*Leaving the door attached makes it easier to align the drawer when
reinstalling it later. It must be straight or the gasket will gap.
a) Put a thick towel on the floor, in front of the unit, so the door
can be laid upon in without scratching the handle or the floor.
b) Pull the drawer out and look at each track about 2/3 of the way
to the back of the freezer. You will see two long, white tabs.
c) Push a tab in while pulling the track slightly forward. Firm pulling
is required. Repeat on the other side.
d) Drag the towel and door out of the way

D) Remove the air grill at the top, rear of the freezer.
1) There is a clip in the center to push with a spudger.
It is easy to see in a photo of a replacement fan bracket.
2) On the right side, in the top row of square holes, is another clip
to press with a spudger while pulling that side of the grill out.
3) On the left, there is an air chute blocking the clip. It can not be
removed. With the right side pulled free, gently wiggle & pull the
left side until the clip clears & the grill is free to leave.

E) Remove the Ice Maker (Water does not have to be turned off)
1) Loosen, but do not remove, 2 screws above the ice mold.
2) Remove the one lower screw & put it aside.
3) Lift the ice maker & store it out of the way.
4) Do Not turn any wheels by hand, nor bend the bail wire.

F) Remove the Thermistor Cover (Upper Right Back Wall)
1) Gently squeeze the sides while pulling. Stop as soon as it's free.
2) Note how the thermistor & wires are installed in the cover &
thread the thermistor free.
3) Set the cover aside.

G) Remove The back Wall
1) Remove all visible hex head screws.
2) The back wall can now be removed.
3) Set it aside where it will not scratch any surfaces, as the edges
are a little sharp

H) De-Ice the evaporator with a heat gun or hair dryer.
Don't hold the heat source in one spot for long or wire insulation
or plastic components will be damaged.

I) Note the permanent ice ball in the upper-right corner.
The defrost thermostat is under this ball. Melt it with heat.

J) Install The New Thermostat
Hint- Take the thermostat to a hardware store to buy the
correct size shrink tube and crimp sleeves (butt connectors)

Followed video on your site. It was very helpful.
Thank you.

Installed a new Defrost Thermostat.

Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.