E23BC78IPSC Electrolux Refrigerator - Instructions

The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!

Following previous installation instructions was very useful. Would add that the nut driver needs to be 1/4 in and to release the water lines from the valve body, simply squeeze the blue ring toward the valve and pull on the water lines at the same time. Simple fix!

Just follow the instruction that come with the valve. Easy.

We followed the online instructions and tah-dah it was working...

Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).

remove the old one and replace with the new one and yes it was that easy. All of the lines and wiring connectors were color coded

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

Removed lower cardboard cover, shut off water supply valve, unpluged frig. Used wrench to remove 3/8 water line from water valve, removed electrical connectors from solenoids, used fingers to unscrew water connections from valve.

This is an easy repair. Unplug appliance. Remove the old water valve by unscrewing it from the frame of the refrigerator. Disconnect the cables and all the water hoses. The hose fittings are a different type: clip off the old connectors from the hose ends and push the hoses straight into the new connectors till they fit solidly. Reconnect the cables and screw the valve back onto the frame of the refrigerator.
Unfortunately, my leak was from a hose, not the valve, so this didn't actually fix it.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

removal of the old valve to identify the problem took the most time. Once the new valve came it it was easy. NOTE: the old one had threaded connectors, and the new one is press/fit so the ends of the tubing need to be cut. The color coding and size matching are great.