E23BC68JPSDA Electrolux Refrigerator - Instructions

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

Remove the crisper drawers. Lift the crisper frame and shelf up and out. Place on a flat surface glass side down. Remove all the Phillips screws holding the frame and the 4 drawer slides. Replace the frame and reassemble.

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

problem still persists part did not fix problem. made repairs recommended per your site.

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI