EI28BS36IB4 Electrolux Refrigerator - Instructions

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963

Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.