E23BC68JPS3 Electrolux Refrigerator - Instructions

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.

Unplugged frig. removed old switch with the aid of screw driver. removed wires and taped; plugged frig. back in and waited for new one. new one came, unplugged frig.removed tape from wire clips plugged in to switch and pushed switch into socket hole and plugged frig. back in; shut door, works like a new one.

problem still persists part did not fix problem. made repairs recommended per your site.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

found the coil to be frozen like a block of ice. defrosted same, then looked up what defrost thermastat i needed and once it was received, i took the back of the freezer compartment off again, (two hex nuts, one on each end, and a small screwdriver to remove guard around fan. once this was removed, you then remove this panel, and you will see the evaperator coil, which will be frozen like a block of ice like i said. then remove defrost therm(small round piece with two wires connected to unit, disengage and re engage new thermostat. then put unit back!. no more freeze ups.also, therm was on top right of evaPERATOR. IT also snaps off on the bottom of thermastat. (just pull to or away from you and it should come off.

took old valve off one peice of it was broke off from freeze replaced it with new valve all but one conection was quick connect electric connections were color coded quick fix works fine thanks Gary

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.