E32AR75FPS0 Electrolux Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wayne from Elkhart, IN
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Blade was broken off of fan.
I removed the back panel ,cardboard-three screws,pushed the old fan blade off the motor and pushed the new fan on.Extremely easy.
Was this instruction helpful to you?
Thank you for voting!
Light on red to change filter
Removed old filter with push of a button and inserted new. Be sure to remove plastic covers on end of new filter before installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Metairie, LA
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Not making ice and not dispensing water.
Just like the instructions said. It took less than 30 seconds. Very happy I could do this myself. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CANTON, IL
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty water filter
unplugged the old one and pushes in the new one DONE IN LESS THAN 6 Min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from petaluma, CA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY from LIBERTY CENTER, IN
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Filter Was Dirty Slid It Out
Slid the new one in easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Hainesport, NJ
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace water filter
take out the old....put in the new...couldn't be easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Ridge Spring, SC
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken blade on fan.
Used needle nose pleirs to slide the old fan off.Then slide the new fan on the spindle.The video really made this easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Cocoa, FL
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Fan Blade had broke off
This repair on this model is super easy because the shroud for the fan is not really attached except for the bottom so I was able to gently bend it to give em enough space to pull the broken fan off and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Gilroy, CA
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
condenser fan stop working
Replaced fan. I ordered the fan and received it the following.(-:
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph f from Boscawen, NH
- Parts Used:
- 240338313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bathroom door
Just took old knob out put new knob in real easy thank you jd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Clovis, NM
- Parts Used:
- 297309000, 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator Fan Motor was making loud rattling sound.
Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ooltewah, TN
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Red light came on for routine filter change out.
Pulled the old filter out and pushed the new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from PRESCOTT VALLEY, AZ
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy fan
Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Satellite Beach, FL
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan would not start occasionally
I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.
Was this instruction helpful to you?
Thank you for voting!