E23CS78EPS1 Electrolux Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shelby from Clinton, IL
- Parts Used:
- 241688401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The ice chute door didn't close all the timed
The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Belmont, OH
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Water Wasn't Filling Ice Tray To Make Ice.
Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Louisville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Ice Maker wasn't making ice
I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.
I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.
I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.
Was this instruction helpful to you?
Thank you for voting!
a crisper cover support had broken
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from AMARILLO, TX
- Parts Used:
- 240597203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Gautier, MS
- Parts Used:
- 241559801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light Socket short
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmelo from Howell, NJ
- Parts Used:
- 241680002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to Ice and water dispenser
First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim back and the drip tray. surprisingly Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Eden Prairie, MN
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Fridge side too cold
Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DOYLESTOWN, PA
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Shelf Broken
Simply slid glass into frame & it fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
2 broken shelving supports
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Anderson, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Buffalo Grove, IL
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lithia, FL
- Parts Used:
- 240328201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Refrig door would not close automatically
Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Herington, KS
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut properly
Removed the door and installed ne bushing on bottom of hinge
Was this instruction helpful to you?
Thank you for voting!