DYF48BIWS00 Dacor Refrigerator - Instructions

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was already started!!! Fast and easy repair!!!

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

I went online and watched a U-tube video that said it was most likely the electronic emitter and receiver boards and showed how to replace them. I first unplugged the appliance (just to be safe) then, I unscrewed the screws holding the faceplate on. The board simply has a plug which you unplug with a little care and effort. I then plugged in the new board, resituated it into the hole and screwed the faceplate back on. You simply do the same for the other board on the other side. Viola! Lots and lots of ice!! The guy at sears said I shouldn't do work on such a complex appliance. Probably because I am a woman! Anyone can do this job! Winning!

My icemaker quit 3 years back and at that time I searched for do-it yourself repair books with no success. I found this parts place web site and people having the same problems as myself. I purchased the parts as others have and problem solved! Ice all the time, woo hoo!

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

After unplugging refrigerator, removed emitter and receiver cover plates on each side of freezer unit (3 screws each) and mounting screws for circuit boards. Unplugged old boards and plugged in new ones and reinstalled boards and then cover plates. Although, indicator code lights seem to still indicate a problem, ice maker has resumed operating after 24 hr.

I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this may have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.

running like a brand new

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.