WRS23MW3AWK Crosley Refrigerator - Instructions

Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

First I removed the plastic drip pan that catches the ice and water. There were two or three screws that had to be removed. Next I removed the old broken actuator and put the new one in. There were two more screws to be removed to replace the old actuator. Those screws were pretty small and hard to get out. Other than that, the new actuator went right in and was working in no time. Overall a pretty easy project.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

Fantastic!
Sent in a brief description of problem and model number. Reply and description of other customers experiences guided us to the exact problem.
We ordered the part on Friday and it was here on Tuesday.
I prepared the freezer compartment for the removal of the old motor and on Sunday husband installed new Evaporator Fan Motor.

It works and is cooling like it did when it was new.

This has been a great experience as all repairmen wanted at least 60.00 to just come out and determine what the problem was. I can only imagine what the final bill would have been.

This was easy and inexpensive.

Thanks for all the help.

Call before ordering and confirm it is the right part.

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!