CRSH232PB8A Crosley Refrigerator - Instructions

Call before ordering and confirm it is the right part.

got replacement ice container with ice crusher and dispenser in the door. removed broken one and slid in the new one like a drawer and started crushing ice right away!!

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.

Remove the screws that hold the old valve to the side of the refrigerator. Next, detach each plastic tube and attach that tube to the same place on the new valve, and repeat (there are many valves). Afterward, I realized that many of the plastic tubes had become brittle and had mineral deposits, so I bought additional tubing for ice makers and replaced each tube, one at a time.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Watched repair video on plastic auger repair and decided to just invest in the whole replacement unit. 45 minute vs. a 5 minute repair.....no brainer. Removed shipping materials from new dispenser, placed on counter top. Removed old ice dispenser, dumped existing ice into new dispenser. Installed new dispenser with ice back into freezer. Tested and unit now dispenses ice.. Easiest fix I've done to date.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

At first glance I didn't see the screws that would permit me to get to the actuator but I lifted the small tray at the bottom and there were two screws. Everything went easily.

Remove power from refrigerator. Pull out the drip tray below paddle. Removed the 3 screws behind tray. Gently pull control panel out and remove the ribbon cable plug from panel. Set panel aside. Remove three screws holding panel housing to door, then pull out housing slightly and disconnect harness plug behind left side of housing. Pull housing out 3-4 inches. Look at the way paddle tabs engage ice dispenser switch mechanism. Remove the left paddle hinge screw and plate and loosen the right hinge screws(these also hold the water paddle hinge) Remove broken paddle by pulling out from right hinge plate and down. Install new paddle under right hinge plate, engage new paddle tabs correctly onto dispenser switch, install left hinge plate and screw, then tighten hinge screws. Reconnect harness plug, reinstall 3 housing to door screws, reconnect ribbon plug to control panel and reinstall panel screws. Reinstall drip tray. Reconnect power to refrigerator and check operation of ice and water paddles.